• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Doctoral Thesis
DOI
https://doi.org/10.11606/T.3.2019.tde-18072019-081017
Document
Author
Full name
Vitor Scarabeli Barbosa
E-mail
Institute/School/College
Knowledge Area
Date of Defense
Published
São Paulo, 2019
Supervisor
Committee
Ruggieri, Claudio (President)
Burgos, Diego Felipe Sarzosa
Godefroid, Leonardo Barbosa
Júnior, Eduardo Hippert
Miranda, Carlos Alexandre de Jesus
Title in Portuguese
Investigação experimental dos efeitos de geometria e de carregamento sobre a distribuição dos valores de tenacidade à  fratura por clivagem medidos na região de transição dúctil-frágil de um aço estrutural ferrítico.
Keywords in Portuguese
Aço
Corpo de prova PCVN não padronizado
Corpo de prova SE(B) não padronizado
Curva mestra
Efeitos de restrição
Fratura por clivagem
Mecânica da fratura
Temperatura de referência
Abstract in Portuguese
Este trabalho aborda uma investigação numérica-experimental sobre o comportamento à fratura por clivagem de um aço de alta resistência e baixa liga ASTM A572 Grau 50 usando corpos de prova SE(B) em configurações padronizadas e não padronizadas, incluindo a configuração PCVN não padronizada. O principal objetivo desse estudo é contribuir para o desenvolvimento de um procedimento de ensaio de tenacidade à fratura aplicável a geometrias SE(B) com distância entre apoios variável (S/W) e carregada sob configuração de flexão por 3 e 4 pontos. O objetivo secundário, mas não menos importante, é investigar os efeitos da geometria e do modo de carregamento sobre as distribuições dos dados de tenacidade à fratura medidas experimentalmente e suas implicações na caracterização da dependência da tenacidade em relação à temperatura baseada na metodologia da curva mestra. Com base nesses propósitos, é fornecido um novo e extenso conjunto de fatores plásticos eta (?p) aplicáveis às geometrias SE(B) não padronizadas para estimar os valores de tenacidade à fratura, incluindo a integral J e o parâmetro CTOD, medidos experimentalmente em termos de registros de carga e deslocamento. A fim de facilitar o contato com os demais protocolos de ensaios, é também fornecido um novo conjunto de fatores rotacionais plástico (rp) para determinar o CTOD baseado no modelo da rótula plástica. Os ensaios de tenacidade à fratura, realizados em diversas geometrias SE(B) com distância entre apoios variável (S/W) extraídas na direção transversal (T-L) de uma chapa de aço ASTM A572 Grau 50, fornecem os dados de tenacidade à fratura por clivagem em termos da integral-J medida no ponto de instabilidade, Jc. Os resultados experimentais mostram um potencial efeito da geometria do corpo de prova e do modo de carregamento sobre os valores de Jc, os quais podem ajudar a mitigar os efeitos da perda de restrição plástica frequentemente observada em corpos de prova de pequenas dimensões. A aplicação exploratória para determinar a temperatura de referência, T0, a partir da metodologia da curva mestra também fornece um suporte adicional para o uso de corpos de prova SE(B) não padronizados como uma alternativa geométrica nos procedimentos rotineiros de avaliação de tenacidade à fratura, incluindo o uso de corpos de prova de pequenas dimensões nas medições de tenacidade quando a disponibilidade limitada de material e a capacidade de carregamento da máquina são as principais preocupações.
Title in English
Experimental investigation of the effects of geometry and loading mode on the cleavage fracture toughness data distribution measured in the ductile-to-brittle transition region of a ferritic structural steel.
Keywords in English
Cleavage fracture
Constraint effects
Master curve
nonstandard precracked Charpy-type Specimen
Nonstandard single-edge notched bend specimen
Reference temperature
Abstract in English
This work addresses a numerical-experimental investigation on the cleavage fracture behavior of an ASTM A572 Grade 50 high strength, low alloy structural steel using standard and non-standard SE(B) specimens, including a non-standard PCVN configuration. The main purpose of this study is to contribute to the development of a fracture toughness test procedure applicable to bend geometries with varying specimen span over width ratio (S/W) and loaded under 3-point and 4-point flexural configuration. The secondary purpose, but none the less important, is to investigate the effects of geometry and loading mode on experimentally measured fracture toughness data distributions and implications for the characterization of the temperature dependence of toughness based on the Master Curve methodology. Based on these purposes, a large new set of plastic ?-factors applicable to these non-standard bend geometries which serve to estimate the experimentally measured toughness values in terms of load-displacement records, including the J-integral and the crack tip opening displacement (CTOD), is provided. In order to facilitate contact with other test protocols, a new set of rotational factors, rp, to determine the CTOD based on the plastic hinge model is also described. Fracture toughness testing conducted on various bend geometries with varying specimen span (S/W) extracted in the T-L orientation from an A572 Grade 50 steel plate provides the cleavage fracture resistance data in terms of the J-integral at cleavage instability, Jc. The experimental results show a potential effect of specimen geometry and loading mode on Jc-values which can help mitigating the effects of constraint loss often observed in smaller fracture specimens. An exploratory application to determine the reference temperature, T0, derived from the Master Curve methodology also provides additional support for using non-standard bend specimens as an alternative specimen geometry in routine fracture assessments, including the use of small-scale fracture specimens to measure fracture toughness properties when limited material availability and test machine capacity are of major concern are of major concern.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2019-07-24
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.