• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.43.2008.tde-18112008-143638
Document
Author
Full name
Fernando Massa Fernandes
E-mail
Institute/School/College
Knowledge Area
Date of Defense
Published
São Paulo, 2008
Supervisor
Committee
Salvadori, Maria Cecilia Barbosa da Silveira (President)
Added, Nemitala
Zambom, Luís da Silva
Title in Portuguese
Síntese de nanotubos de carbono orientados e aplicação na produção de pontas de AFM
Keywords in Portuguese
Nanotubos de carbono
Pontas de AFM Tips
Abstract in Portuguese
Neste trabalho foram obtidos nanotubos de carbono de paredes múltiplas (MWNT). O crescimento apresentou alta densidade de nanotubos orientados perpendicularmente à superfície do substrato, com cerca de 20 m de comprimento e diâmetros entre cerca de 20 e 60 nm. Foram utilizados filmes catalisadores contendo ferro, depositados a partir de solução de nitrato de ferro (Fe(NO3)3.9H2O) em álcool etílico com concentrações que variaram entre 37 mmol/L e 1,2 mmol/L. Não foram notadas diferenças significativas entre os nanotubos crescidos com diferentes concentrações, com exceção da solução de 0,6 mmol/L onde não foi observado o crescimento de nanotubos. Os crescimentos de nanotubos de carbono foram efetuados em um reator CVD a plasma de microonda. Os resultados de espectroscopia Raman sugerem que os nanotubos de carbono obtidos neste trabalho correspondem a MWNT, apresentando alto grau de desordem estrutural. Foram realizados crescimentos diretos de nanotubos de carbono sobre as pontas comerciais de AFM, utilizando filmes de nitrato de ferro. Os nanotubos crescidos nas pontas apresentaram tendência em formarem aglomerados. Não foram obtidas pontas de AFM satisfatórias com este método. Outro método consistiu no crescimento de nanotubos de carbono em amostras planas de silício, utilizando filme catalisador de nitrato de ferro com posterior captura de nanotubos na extremidade da ponta, utilizando um microscópio AFM. Foram realizados 26 procedimentos, onde a maioria dos resultados não foi satisfatória. Apenas em dois dos procedimentos foram obtidos resultados muito bons com nanotubos de carbono retos e protuberantes emergindo das pontas. Ainda neste trabalho foi desenvolvido um método de reciclagem das pontas. O processo é de grande valia, pois a obtenção de pontas de AFM com nanotubos apresenta sucesso em apenas uma fração do número de tentativas, levando a inutilização de um número representativo de pontas. A reciclagem das pontas foi realizada por meio da corrosão dos nanotubos de carbono em plasma de hidrogênio. O equipamento utilizado para essa finalidade foi o próprio reator CVD a plasma de microonda, também utilizado para o crescimento dos nanotubos.
Title in English
Oriented growth of carbon nanotubes and application in production of afm Tips
Keywords in English
AFM Tips
Carbon nanotubes
Abstract in English
In this work multi walled carbon nanotubes (MWCNT) were obtained. The growth presented high density nanotubes oriented perpendicularly to the substrate, with about 20 m length and diameters between 20 and 60 nm. Catalytic films containing iron were used. These films were deposited from solution of iron nitrate (Fe(NO3)3.9H2O) in ethyl alcohol with concentrations that varied between 37 mmol / L and 1.2 mmol / L. It was not observed significant difference among the grown nanotubes obtained with different concentrations, except from the solution of 0.6 mmol / L, where the nanotubes growth was not observed. The growths of carbon nanotubes were obtained in a microwave plasma CVD reactor. The Raman spectroscopy suggests that the carbon nanotubes obtained in this work correspond to MWCNT, presenting high degree of structural disorder. Direct growths of carbon nanotubes on commercial AFM tips were performed, using films of iron nitrate. The nanotubes grown directly on the tips presented tendency in forming agglomerates. They were not obtained satisfactory AFM tips with this method. Another method consisted of carbon nanotubes growth on flat silicon substrates, using catalytic film of iron nitrate, with subsequent nanotubes capture at the extremity of the tip, using a microscope AFM. Altogether 26 procedures were performed, where most of their results were not satisfactory. In just two of these procedures were obtained very good results with straight and protuberant carbon nanotubes emerging of the tips. Still in this work a method of tip recycling was developed. The process is valuable, since the success in obtaining AFM tips with nanotubes occurs in just a fraction of the attempts, generating a representative number of lost tips. The tips recycling were performed through the corrosion of the carbon nanotubes in hydrogen plasma. The equipment used for this purpose was the microwave plasma CVD reactor, also used for carbon nanotubes growth.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2008-11-24
 
WARNING: The material described below relates to works resulting from this thesis or dissertation. The contents of these works are the author's responsibility.
  • Salvadori, M. C., et al. Novel method for measuring nanofriction by atomic force microscope [doi:10.1116/1.2890694]. Journal of Vacuum Science & Technology. B, Microelectronics and Nanometer Structures Processing, Measurement and Phenomena [online], 2008, vol. 26, p. 643-650.
  • FERNANDES, F M, TEIXEIRA, F S, e SALVADORI, M. C. Efeito da espessura do filme de metal catalítico na morfologia das partículas metálicas e sua influência nos nanotubos de carbono crescidos por PECVD. In XXIX Encontro Nacional de Física da Matéria Condensada, São Lourenço, 2006. Livro de Resumos do XXIX Encontro Nacional de Física da Matéria Condensada., 2006. Resumo.
  • LISBOA, Fábio dos Santos, et al. DLC friction coefficient measurement by AFM. In 2nd International Symposium on Advanced Materials and Nanostructures, São Carlos, 2007. Abstracts of the 2nd International Symposium on Advanced Materials and Nanostructures., 2007. Abstract.
  • Salvadori, M.C., et al. DLC friction coefficient measured by AFM using a DLC coated tip. In VII Encontro sobre diamante, carbono amorfo, nanotubos de carbono e materiais relacionados, Fortaleza, 2007. Resumos do VII Encontro sobre diamante, carbono amorfo, nanotubos de carbono e materiais relacionados., 2007. Resumo.
  • WIEDERKEHR, Rodrigo Sérgio, et al. Numerical study of a piezoelectric microvalve using continuum methods. In 17th IEEE University/ Governement/ Industry Micro/Nano Symposium 2008, Louisville, Kentucky, Estados, 2008. Proceeding of the 17th IEEE University/Governement/Industry Micro/Nano Symposium 2008., 2008.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.