• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Tese de Doutorado
DOI
https://doi.org/10.11606/T.3.2018.tde-28022018-104215
Documento
Autor
Nome completo
Jaime Casanova Soeiro Junior
E-mail
Unidade da USP
Área do Conhecimento
Data de Defesa
Imprenta
São Paulo, 2017
Orientador
Banca examinadora
Brandi, Sérgio Duarte (Presidente)
Monlevade, Eduardo Franco de
Poetscher, Freddy
Silva, Pedro Miguel dos Santos Vilaça da
Souza, Paulo Cézar Rioli Duarte de
Título em português
Soldabilidade metalúrgica do aço ASTM A553 tipo I com 9% de ní­quel.
Palavras-chave em português
Aço níquel
Soldabilidade metalúrgica
Soldagem
Soldagem por atrito linear
Resumo em português
A soldagem altera as propriedades mecânicas dos aços ligados ao níquel, em especial seu desempenho em aplicações criogênicas. Assim, este trabalho apresenta um estudo sobre a soldabilidade metalúrgica do aço com 9% níquel e tem como objetivos: identificar se a fragilização em temperatura abaixo da temperatura Ac3 ocorre em ZACs com dois e três ciclos térmicos simulados fisicamente; analisar as características da junta soldada pelo processo de soldagem por atrito linear com mistura e os efeitos da soldagem multipasse; e analisar a influência dos passes de enchimento e acabamento sobre o comportamento mecânico da ZAC da raiz de uma junta soldada pelo processo de soldagem MIG/MAG. Destacam-se entre os resultados da simulação física da ZAC: as amostras que tiveram a temperatura máxima abaixo da temperatura Ac1, no terceiro ciclo térmico, não apresentaram o efeito de redução da energia absorvida no ensaio Charpy V; a fração volumétrica de austenita retida não aumenta a quantidade de energia absorvida no ensaio Charpy V para as amostras que tiveram a temperatura máxima do segundo ciclo térmico abaixo da temperatura Ac3 (723°C); e a correlação linear múltipla sugere um modelo empírico, baseado nos dados deste trabalho, onde os fatores de fração volumétrica do microconstituinte martensita-austenita, fração volumétrica de austenita retida e tamanho de grão são mais relevantes para a quantidade de energia absorvida no ensaio Charpy V. Destacam-se entre os resultados da soldagem por atrito linear: a energia absorvida no ensaio Charpy V da zona misturada do primeiro cordão (CP1) é menor que o metal de base; o segundo cordão gera duas regiões na zona misturada do primeiro cordão, que tendem a aumentar a energia absorvida no ensaio Charpy V; os valores de energia absorvida no ensaio Charpy V apresentam correlações lineares simples com a microdureza, a fração volumétrica do microconstituinte martensita-austenita e com o tamanho de grão. Destacam-se entre os resultados da soldagem com MIG/MAG: A soldagem do aço com 9% de níquel com a liga Inconel 625 gera uma zona não misturada entre o metal de solda e a ZAC; a amostra com todos os passes de solda (CP3) apresenta a menor energia absorvida no ensaio Charpy V entre todos os experimentos; e a trinca, no ensaio Charpy V, propaga na zona não misturada no CP1 e no CP2, que tiveram as maiores energias absorvidas no ensaio Charpy. O CP3 apresenta propagação de trinca na linha de fusão e possui a menor energia absorvida no ensaio Charpy V.
Título em inglês
Metallurgical weldability of ASTM A553 Type I steel with 9% nickel.
Palavras-chave em inglês
9 % nickel steel
Effect of the filling and finishing passes on the root HAZ
Friction stir welding
Metallurgical weldability
Resumo em inglês
Welding modify the mechanical properties of nickel steels, especially their performance in cryogenic applications. Thus, this work presents a study on the metallurgical weldability of 9% nickel steel and its objectives are: identify if the embrittlement in temperature below the Ac3 temperature occurs in HAZs with two and three thermal cycles simulated physically; analyze the characteristics of the joint welded by friction stir welding process and the effects of multipass welding; and analyze the influence of the filling and finishing passes on the mechanical behavior of HAZ from the root of a joint welded by the GMAW welding process. The results of the physical simulation of the HAZ were: the samples that had the maximum temperature below the temperature Ac1, in the third thermal cycle, did not present the effect of reduction of the energy absorbed in the Charpy V test; the retained austenite volumetric fraction does not increase the amount of energy absorbed in the Charpy V test for the samples having the maximum temperature of the second thermal cycle below the Ac3 temperature (723 °C); and the multiple linear correlation suggests an empirical model, based on the data of this work, where the volumetric fraction factors of the martensite-austenite microconstituent, retained austenite volumetric fraction and grain size are more relevant for the amount of energy absorbed in the Charpy V test. The FSW welding highlights results: the energy absorbed in the Charpy V test of the mixed zone of the first pass (CP1) is smaller than the base metal; the second pass generates two regions in the mixed zone of the first pass, which tend to increase the energy absorbed in the Charpy V test; the values of energy absorbed in the Charpy V test show simple linear correlations with the microhardness, the volumetric fraction of the martensite-austenite microconstituent and with the grain size. The GMAW welding highlights results: welding of the steel with 9% nickel with the Inconel 625 alloy makes an unmixed zone between the weld metal and the HAZ; the sample with all weld passes (CP3) shows the lowest energy absorbed in the Charpy V test among all the experiments; and the crack, in the Charpy V test, propagates in the unmixed zone in CP1 and CP2, which had the highest energies absorbed in the Charpy test. The CP3 shows crack propagation in the melting line and has the lowest energy absorbed in the Charpy V test.
 
AVISO - A consulta a este documento fica condicionada na aceitação das seguintes condições de uso:
Este trabalho é somente para uso privado de atividades de pesquisa e ensino. Não é autorizada sua reprodução para quaisquer fins lucrativos. Esta reserva de direitos abrange a todos os dados do documento bem como seu conteúdo. Na utilização ou citação de partes do documento é obrigatório mencionar nome da pessoa autora do trabalho.
Data de Publicação
2018-03-07
 
AVISO: Saiba o que são os trabalhos decorrentes clicando aqui.
Todos os direitos da tese/dissertação são de seus autores
CeTI-SC/STI
Biblioteca Digital de Teses e Dissertações da USP. Copyright © 2001-2024. Todos os direitos reservados.