• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.3.2007.tde-19072007-163542
Document
Author
Full name
Ronaldo Ferreira da Costa
E-mail
Institute/School/College
Knowledge Area
Date of Defense
Published
São Paulo, 2007
Supervisor
Committee
Schon, Cláudio Geraldo (President)
Pavanello, Renato
Plaut, Ronald Lesley
Title in Portuguese
Efeitos dos parâmetros de usinagem na formação da camada branca em torneamento duro nos aços-rolamento (DIN 100 Cr6).
Keywords in Portuguese
Acabamento de superfícies
Parâmetros de respostas
Usinagem
Abstract in Portuguese
Este trabalho discute as alterações micro-estruturais superficiais nos aços usinados por torneamento duro. Uma estrutura não aceita metalurgicamente, chamada de Camada Branca ("White Layer" - WL), é freqüentemente encontrada na superfície torneada. A presença desta camada branca depende dos parâmetros do processo de corte, especialmente do desgaste da ferramenta e da velocidade do corte. A formação da camada branca foi investigada no presente trabalho na face plana inferior de um anel de rolamento fabricada com o aço DIN 100Cr6, usinada por torneamento duro no estado temperado e revenido (dureza 60HRC). A profundidade foi medida usando as técnicas padrões metalográficas. As propriedades mecânicas da camada superficial (módulo de rigidez, E, e microdureza Vickers, HV) foram estimadas pelo método de microidentação instrumentada em uma amostra isenta da camada branca e em duas outras amostras, com camadas brancas de diferentes espessuras (respectivamente 7 e 12 mm de espessura). De acordo com a literatura a profundidade da camada branca aumenta de acordo com o desgaste da aresta da ferramenta. Este por sua vez aumenta com a velocidade de corte, mas atinge a saturação. Em outras palavras, a profundidade de corte tem pouco efeito sobre a profundidade da camada branca; porém aumentando o avanço da ferramenta de corte ocorre o aparecimento da mesma. Os presentes resultados confirmam um efeito do avanço da ferramenta sobre a espessura da WL, tal que quanto menor o avanço, maior é a espessura, porém não confirmam o efeito do desgaste da ferramenta. A formação desta camada é discutida no contexto da sua influência sobre a rugosidade das peças.
Title in English
Effects of machining parameters upon the development of the white layer in hard turning of bearing steels (DIN 100 Cr6).
Keywords in English
Machining
Response parameters
Surface finishing
Abstract in English
This work deals with the microstructural changes in the surface of steels machined by hard turning. A non-acceptable microstructure, called White Layer - WL, is usually found in the hard turned surface. The presence of the white layer depends on hard turning parameters, especially on the wear of the machining tool and cutting speed. The formation of the white layer was investigated in the present work by hard turning the inferior face of a roller-bearing ring fabricated with DIN 100Cr6 steel quenched and tempered (60 HRC hardness). The depth of the WL was measured by standard metallographic procedures. The mechanical properties (stiffness modulus, E, and Vickers hardness) of the surface layer were measured by intrumented indentation in three samples: one with no WL, and two containing a WL of respectively 7 and 12 mm. According to the literature the depth of the WL increases with the wear of the machining tool. This increased with cutting speed, but reaches saturation. The presentresults confirm an effect of tool advance upon the depth of the WL, such that decreasing the advance leads to an increase in its depth, but an effect of tool wear could not be recognized. The formation of the WL is discussed in the context of its effect on surface roughness.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2007-08-15
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.