• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.18.2019.tde-06082019-112047
Document
Author
Full name
Fábio Faria Conde
Institute/School/College
Knowledge Area
Date of Defense
Published
São Carlos, 2019
Supervisor
Committee
Bose Filho, Waldek Wladimir (President)
Lopes, Éder Socrates Najar
Nossa, Tamires de Souza
Title in Portuguese
Avaliação microestrutural e mecânica de peças de Aço Maraging 300 fabricadas por manufatura aditiva usando fusão seletiva a laser e submetidas a tratamentos térmicos
Keywords in Portuguese
análise in-situ síncrotron e ex-situ
cinética de reversão martensita-austenita
manufatura aditiva
maraging 300
simulação termodinâmica do 18 Ni.
tratamentos cíclicos e isotérmicos para reversão
Abstract in Portuguese
O aço maraging é conhecido pela sua alta resistência mecânica proveniente da formação de precipitados intermetálicos como Ni3Ti e Fe2Mo durante o envelhecimento, porém com subsequente perda de tenacidade à fratura. Existe uma vasta literatura sobre este tipo de aço, o qual é submetido a diversos tratamentos térmicos. Normalmente dois tratamentos térmicos são aplicados: uma homogeneização inicial para solubilização dos precipitados, sendo a recomendação geral 820 °C/1 h, e posteriormente o tratamento de envelhecimento, variando a temperatura de 455 °C a 510 °C e o tempo de 3 a 12 h. No entanto, pode haver variações no tratamento, como aquecimento após homogeneização numa faixa de temperatura intercrítica ou abaixo da Ac1 visando a reversão da martensita em austenita e o refino de grão. Até o presente momento, não está bem definida a influência da temperatura/tempo em tratamentos de temperaturas inter ou subcríticas que visam o refinamento da estrutura e o aumento da austenita retida/reversa. A literatura mostra tratamentos na liga maraging 300 por meio de estudos mais antigos, da década de 70 e 80, utilizando aquecimentos curtos e cíclicos para reversão e estabilização da austenita reversa. Estudos mais recentes de outras ligas utilizaram tratamentos isotérmicos para difusão e reversão da martensita em austenita. Nesta proposta serão pesquisadas as duas rotas de tratamento, cíclica e isotérmica, para avaliar a reversão martensita-austenita. Os tratamentos cíclicos foram caracterizados por EBSD, MEV e difração de raio-X ex-situ. Os tratamentos isotérmicos foram caracterizados por EBSD e difração de raio-X de fonte sincrotron in-situ, ou seja, medida em tempo real durante o tratamento. Ambas as condições foram avaliadas mecanicamente por meio de ensaios de flexão de 3 pontos.
Title in English
Microstructural and mechanical evaluation of maraging 300 steel parts manufactured by additive manufacturing using selective laser fusion and subjected to thermal treatments
Keywords in English
additive manufacture
cyclic and isothermal treatments for martensite-to-austenite reversion
maraging 300
martensite-to-austenite reversion kinetics
synchrotron in-situ and ex-situ analysis
thermodynamic simulations of 18 Ni
Abstract in English
Maraging steel is known for its high mechanical strength resulting from the formation of intermetallic precipitates such as Ni3Ti and Fe2Mo during aging heat treatment, with subsequent loss of fracture toughness. There is a vast literature on this type of steel, which is subjected to various thermal treatments. Normally two heat treatments are applied: an initial homogenization for solubilization of the precipitates, the general recommendation being 820 ° C/1 h, and later the aging treatment, varying temperature from 455 ° C to 510 ° C and time of treatment from 3 to 12 hours. However, there may be applied other heat treatments, such as heating after homogenization in an intercritical temperature range or below Ac1 for the reversion of martensite-to-austenite and grain refinement. To date, the influence of temperature and time on inter- or subcritical temperature treatments aiming at grain refinement and martensite-to-austenite reversion is not well defined. The literature shows treatments in the maraging 300 alloy, from the 70s and 80s, using short and cyclic heat treatment for reversion and stabilization of austenite. Recent studies of other alloys have used isothermal treatments for diffusion and martensite-to-austenite revresion. In this study, two heat treatment routes, cyclical and isothermal, were investigated to evaluate the martensite-to-austenite reversion. Cyclic treatments were characterized by EBSD, SEM and ex-situ X-ray diffraction. The isothermal treatments were characterized by EBSD and X-ray diffraction of synchrotron source in-situ, that is, measured in real time during the treatment. Both conditions were mechanically evaluated by 3-point-bending tests.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2019-08-22
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.