• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.18.2015.tde-13102015-152550
Document
Author
Full name
Guilherme Henrique Favaro Fuzato
Institute/School/College
Knowledge Area
Date of Defense
Published
São Carlos, 2015
Supervisor
Committee
Machado, Ricardo Quadros (President)
Aguiar, Manoel Luís de
Gules, Roger
Title in Portuguese
Análise de um conversor boost interleaved com multiplicador de tensão para sistemas de geração distribuída que utilizam células a combustível como fonte primária
Keywords in Portuguese
Célula a combustível
Controle
Conversores CC-CC
Fontes alternativas
Geração distribuída
Abstract in Portuguese
Esta dissertação aborda aspectos gerais relativos à utilização de um conversor CC-CC que opera conectado à rede de distribuição e que emprega como fonte primária células a combustível. Neste trabalho, a modelagem matemática em espaços de estados (pequenos sinais e média) dos conversores Boost e Boost Interleaved com Multiplicador de Tensão (IBVM), assim como as arquiteturas de controle utilizadas em modo tensão, corrente média e corrente de pico são comparadas para determinar qual delas apresenta melhor desempenho. Devido ao fato das células a combustível apresentarem tensão terminal baixa e corrente terminal elevada, há a necessidade de utilizar conversores eletrônicos com alto ganho para equalizar a tensão produzida pela fonte com o nível de tensão presente na rede de distribuição. Tendo isso em vista, este trabalho mostra uma análise do ganho estático de tensão do conversor Boost e IBVM considerando os efeitos das resistências parasitas dos componentes utilizados e da carga conectada nos terminais de saída do conversor. Como resultado da modelagem matemática do ganho, é mostrado um conjunto de equações que definem o valor mínimo de resistência do semicondutor de potência, indutor, capacitor do multiplicador de tensão e a máxima carga que os conversores Boost e Boost Interleaved com Multiplicador de Tensão podem suprir. Por fim, os resultados experimentais são apresentados com o intuito de validar os resultados teóricos e de simulação obtidos.
Title in English
Study of a interleaved Boost with voltage multiplier converter apllied to a grid connected fuel cell system
Keywords in English
Alternative sources
Control
DC-DC converter
Distributed generation
Fuel cell
Abstract in English
This thesis addresses general aspects concerning the application of DC-DC converters applied to a grid connected Fuel Cell system. It is discussed in this thesis the averaged and small signals space state modeling of the Boost and Interleaved Boost with Voltage Multiplier (IBVM) converter, it is also mentioned the control architectures in voltage mode, average current mode and peak current mode. The voltage and average current mode control architectures are simulated and implemented in hardware in order to be compared. Due to the fact that Fuel Cells present low terminal voltage and high current, it is needed to use high gain DC-DC converters with the aim connect the system to the grid. This thesis also presents an approach in the analysis of DC-DC converter static voltage gain considering the effect of the parasitic resistances and the load connected to the converter terminals. As a result of the gain analysis, it is presented a set of equation, from which is possible to determine the maximum value of the parasitic resistances for the switch, inductor and capacitor of the voltage multiplier. It is also calculated the maximum value of load connected to the Boost and Interleaved Boost with Voltage Multiplier converters with the aim to present the designed voltage gain. Additionally, by the maximum load value calculated it is possible to determine the maximum power that the converter will be capable to process, considering a specific point of operation. Finally, the designed DC-DC converter is implemented with the aim to validate the theoretical and simulation results.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Guilherme.pdf (8.67 Mbytes)
Publishing Date
2015-10-19
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.