• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.18.2019.tde-25092019-114826
Document
Author
Full name
Kandice Suane Barros Ribeiro
E-mail
Institute/School/College
Knowledge Area
Date of Defense
Published
São Carlos, 2019
Supervisor
Committee
Rodrigues, Alessandro Roger (President)
Hassui, Amauri
Suyama, Daniel Iwao
Title in Portuguese
Monitoramento da condição da ferramenta no microfresamento por meio de sinais de potência e emissão acústica
Keywords in Portuguese
Desgaste da ferramenta
Emissão acústica
Estabilidade de corte
Microfresamento de topo
Monitoramento
Potência
Abstract in Portuguese
Considerando as dimensões reduzidas das ferramentas de microfresamento, a seleção não otimizada dos parâmetros de corte tende a maximizar o desgaste e a quebra da ferramenta durante operações de microusinagem. Isto posto, o desenvolvimento de um sistema de monitoramento para explorar as condições da microfresa durante a usinagem é fundamental. Portanto, o objetivo desta pesquisa é monitorar via sinais de potência e emissão acústica (EA) o desgaste da ferramenta e a estabilidade de corte em operações de microfresamento do aço COS AR60 e COS AR60 de grãos ultrafinos (GUF). Os testes de microfresamento foram realizados com ferramentas de diâmetro de 1 mm e duas arestas, com substrato de metal duro e revestimento (Ti, Al, Cr) N, em um centro de usinagem CNC Romi D800 High Performance adaptado com um cabeçote de alta rotação. O microfresamento ocorreu nos dois materiais sem aplicação de fluido de corte e com velocidade de corte de 62,5 m/min e 125 m/min, mantendo constante a velocidade de avanço de 240 mm/min (fz = 6 μm/aresta e 3 μm/aresta), profundidade de usinagem de 100 m e comprimento de usinagem de 104 mm em corte em cheio. O sinal de potência e EA foram adquiridos à taxa de 5 kHz e 1,25 MHz, respectivamente. Os dados foram adquiridos em LabVIEW® e processados em LabVIEW® e MATLAB®. Os resultados de caracterização dos desgastes apontaram um desgaste de flanco mais expressivo e a formação de Aresta Postiça de Corte (APC) no GUF para vc = 125 m/min, e a presença de desgaste de cratera em todas as condições de corte. O aumento da potência de corte média representou a predominância do desgaste de flanco, e desgaste de cratera em sua redução. De forma semelhante, a ANOVA dos valores de EA RMS indicaram com significância (95% de confiança) uma correlação diretamente proporcional entre EA RMS e evolução do desgaste de flanco na microfresa. Quanto à estabilidade de corte, ambos os sinais apresentaram um aumento expressivo de amplitude quando o corte foi instável. Com isso, os métodos de monitoramento utilizados foram capazes de indicar a evolução do desgaste da microfresa e a ocorrência de chatter em operações de microfresamento.
Title in English
Monitoring of tool condition in micro-milling via cutting power and acoustic emission signals
Keywords in English
Acoustic Emission
Cutting power
Cutting stability
Micro end milling
Monitoring
Tool wear
Abstract in English
Regarding the reduced dimensions of micro-milling tools, a non-optimised selection of cutting parameters tends to maximise tool wear and breakage during cutting operations. Hereupon the development of a monitoring system for exploring microtool conditions during machining is imperative. Therefore, the aim of this research is to monitor tool wear and cutting stability via cutting power and acoustic emission (AE) signals in micro-milling operations of steel COS AR60 and ultra fine-grained steel COS AR 60 (GUF). Cutting tests were performed by carbide endmill tools with (Ti, Al, Cr) N coating, two flutes and 1 mm diameter in a CNC machining centre Romi D800 High Performance adapted with a high spindle speed head. Micro-milling operations were carried out in both materials without cutting fluid application at 62.5 m/min and 125 m/min, and constant parameters of feed, set at 240 mm/min (fz = 6 μm/tooth and 3 μm/tooth), depth of cut of 100 m and cutting length of 104 mm performed in sloth cutting strategy. Cutting power and AE signals were acquired at the rate of 5 kHz and 1.25 MHz, respectively. The data were acquired in LabVIEW® and processed in both LabVIEW® and MATLAB®. The results on wear characterisation revealed a major flank wear and the formation of Built Up-Edge (BUE) in GUF at vc = 125 m/min, along with the occurrence of crater wear in all cutting conditions set. An increase in the average cutting power levels is linked to the predominancy of flank wear, while crater wear to its decrease. Likewise, the Analysis of Variance (ANOVA) of EA RMS values indicated with significancy (95% confidence) a direct proportion between AE RMS and flank wear in the microtool. In terms of cutting stability both EA and cutting power signals have shown an expressive rise when performing instable cutting. Thus, the methods of monitoring were feasible for recognising tool wear evolution and chatter in micro-milling operations.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2019-10-03
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.