• JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
  • JoomlaWorks Simple Image Rotator
 
  Bookmark and Share
 
 
Master's Dissertation
DOI
https://doi.org/10.11606/D.18.2017.tde-30032017-103451
Document
Author
Full name
Maria Ávila Branquinho
Institute/School/College
Knowledge Area
Date of Defense
Published
São Carlos, 2017
Supervisor
Committee
Malite, Maximiliano (President)
Maia, Wanderson Fernando
Vieira Junior, Luiz Carlos Marcos
Title in Portuguese
Sobre o comportamento estrutural e o dimensionamento de cantoneiras de aço formadas a frio submetidas à compressão e conectadas por uma aba
Keywords in Portuguese
Cantoneiras formadas a frio
Comprimento de flambagem equivalente
Confiabilidade estrutural
Estruturas de aço
Instabilidade estrutural
Abstract in Portuguese
A cantoneira de abas iguais é encontrada laminada ou formada a frio. Quando laminada, normalmente possui abas compactas, isto é, se submetida à compressão, não apresenta instabilidade local e, para a faixa usual de comprimentos, não apresenta também o modo global de flexo-torção como dominante. Quando formada a frio, estes modos predominam, uma vez que a relação largura-espessura torna-se elevada. A elevada esbeltez das abas, juntamente com as peculiaridades do seu comportamento mecânico, pode conduzir a significativas divergências entre a força axial resistente (experimental) quando comparada aos valores oriundos dos procedimentos de cálculo apresentados pelas normas. As divergências são ainda maiores quando se considera a cantoneira em sua situação mais usual: sob compressão excêntrica devido à ligação parafusada ou soldada em uma das abas. No presente trabalho foi analisado o comportamento mecânico das cantoneiras formadas a frio e conectadas pela aba por dois parafusos e desenvolvida uma formulação baseada no método do comprimento de flambagem equivalente, bem como identificados seus modos de instabilidade e a respectiva participação modal para diversas faixas de esbeltez. Para validar esta formulação, foi realizada uma análise de confiabilidade que resultou em índices de confiabilidade (β) de acordo com as exigências normativas.
Title in English
On the structural behavior and the design of bolted cold-formed steel angles under compression
Keywords in English
Cold-formed angles
Equivalent buckling length
Steel structures
Structural instability
Structural reliability
Abstract in English
The equal-leg angle is found hot-rolled or cold-formed. When hot-rolled, it usually has compact legs, that is, if subjected to compression it does not present local buckling and it does not present a global flexo-torsion buckling mode as dominant for the usual range of lengths. When cold-formed, these modes predominate, since the width-to-thickness ratio becomes high. The high slenderness of the legs, together with the peculiarities of its mechanical behavior, can lead to significant divergences between the axial strength (experimental) and the values from standard's procedures. The divergences are even greater when considering the angle in its most usual loading situation: under eccentric compression due to bolted or welded connection in one leg. In the present work the mechanical behavior of the cold-formed angles connected by the leg by two bolts was analyzed in order to propose a formulation based on the equivalent buckling length method, as well as, to define its buckling modes and the respective modal participation for different slenderness ranges. To validate this formulation, a reliability analysis was performed that resulted in reliability indexes (β) according to the design standards requirements.
 
WARNING - Viewing this document is conditioned on your acceptance of the following terms of use:
This document is only for private use for research and teaching activities. Reproduction for commercial use is forbidden. This rights cover the whole data about this document as well as its contents. Any uses or copies of this document in whole or in part must include the author's name.
Publishing Date
2017-04-18
 
WARNING: Learn what derived works are clicking here.
All rights of the thesis/dissertation are from the authors
CeTI-SC/STI
Digital Library of Theses and Dissertations of USP. Copyright © 2001-2024. All rights reserved.